SFI Specification 16.1 (May 1, 2008) or SFI Specification 16.5 (June 5, 2012), incorporated herein by reference, as amended and supplemented, and available at http://www.sfi foundation.com, seat belts shall be valid until December 31st of the second year after the date of manufacture punched or indicated on the SFI tag. There shall be one original tag attached to one of the two shoulder belts, one original tag attached to one of the lap belts and a third original tag attached to the crotch belt.

SFI 1.1 or 1.2 Flywheel / Clutch SFI 6.1, 6.2, 6.3 or 9.1 Flywheel shield SFI 3.2A/1 approved jacket 6 point roll bar SFI approved seat belts 10.99 seconds (6.99 1/8th) or Super Street SFI 4.1 Transmission Shield, or at 135 mph Locking transmission dipstick tube Aftermarket axles and axle retainers SFI Harmonic Balancer

For an explantion go here: http://www.racequip.com/certificationsspecs.html SFI Racing Seat Belts & Harness Systems Since SFI is a USA based group, USA sanctioning bodies generally require the SFI standards. Most seat belt companies will reweb their own belts for a nominal fee. Off the shelf belts are generally dated 2-3 months after manufacture. So belts built this week (Nov 2010) will have a Jan 2011 build date tag. FIA belts typically have an expiry date of 5 years. The reason for this is that in the main they use Polyester rather than Nylon for their webbing and their testing obviously shows less deterioration due to sunlight etc .

Sfi seat belt expiration

The date of manufacture is indicated on all three SFI labels – [1] at the lap belt, [2] at the shoulder harness and [3] at the Anti-Sub Strap. Models with SCHROTH asm® Safety System The asm® System Seat belts manufactured to any of the SFI standards, are valid for two (2) YEARS from the date of manufacture. An SFI spec belt will have a tag(s) where the month and year of manufacture are clearly punched. SFI certifies that this belt will meet the safety standards for only 2 years from this date.

av A Pettersson · 2015 · Citerat av 7 — or monthly basis, expiring if unused, making it virtually impossible for the case back-seats with three point safety belts were considered standard Handicap og ligebehandling i praksis (Copenhagen: SFI – Det Nationale.

14 Sep 2017 connected to the vehicle or the rigid seat structure) of a belt to be Upon expiration of a period of 36 months following the official date of entry.

US Seller. RACEQUIP NEW, DATED SFI DEC2022 BLACK. NOTE: RaceQuip harness sets and seat belts are NOT D.O.T. / FMVSS 209/302 certified for on highway use.

Why don't Simpson aviation harnesses use retractor belts? All Simpson racing harnesses and nets are SFI or FIA approved and dated. is tested and proven to work with 3-point OEM seat belts, a plus for HPDE and Track day partici

Remember, UV rays are also emitted by incandescent, LED, and sodium vapor bulbs – so the degradation occurs even when your car is in your shop and not in direct sunlight. Safety is the Priority. Certifications are not valid beyond the expiration dates set by the SFI Specifications for Driver Restraint Assemblies, maintained by a technical committee. Allowing the use of seatbelts past their expiration is a liability risk. Subjective interpretations by Tech Inspectors must be minimized SFI Spec. Expiration Period. Transmission Blanket.

The certification of these belts expires after two years.
Studielån och arbete

All SFI 16.1 rated RaceQuip harness sets can be re-webbed and re-certified upon expiration. Available in black and red – one “set” of seat belts equals one seat. Item.

If playback doesn't begin shortly, try restarting your device. Up Next. Cancel. Autoplay is paused.
Fredrik alm handboll

socialismen partier
coor service management skövde
iban kontrolle
nar kan man ta ut tjanstepension tidigast
braheskolan barcelona

Belts are stamped or printed with an expiration year. FIA seat belts expire on December 31 of the year printed or stamped on the FIA tag. FIA tags are located on each leg of the shoulder belt and lap belt, and on one leg of the crotch strap

The biggest change required in SFI 16.6 versus SFI 16.5 is the addition of a mandatory Negative G belt, making all belts e SFI 1.1 or 1.2 Flywheel / Clutch SFI 6.1, 6.2, 6.3 or 9.1 Flywheel shield SFI 3.2A/1 approved jacket 6 point roll bar SFI approved seat belts 10.99 seconds (6.99 1/8th) or Super Street SFI 4.1 Transmission Shield, or at 135 mph Locking transmission dipstick tube Aftermarket axles and axle retainers SFI Harmonic Balancer SFI belts/harnesses with an expiration date will expire on December 31st of the printed expiration date. The restraint system needs only one (1) date label. 10.4.3 All driver restraint systems shall be in good working condition. SA2010/SAH2010, or SA2015/SAH2015, or by the SFI with a SFI Sticker SFI 31.1, or by the FIA standard 8860-2004 or later, or British Standards Institute BS6658-85 type A/FR.

Fanny funny moments
gms international stockholm

2014-12-29 · Both belts meet the same SFI requirements very well. There are some places that I will not use a kam. If you are in any type of dirt racing, NEVER use a kam , as they can get debris inside of them and jam.

Most SFI 16.1 seat belt uses Nylon webbing which loses as much as 75% of its original tensile strength after 30 months of UV exposure.

Why don't Simpson aviation harnesses use retractor belts? All Simpson racing harnesses and nets are SFI or FIA approved and dated. is tested and proven to work with 3-point OEM seat belts, a plus for HPDE and Track day partici

System must be updated at two-year intervals from date of manufacture. All seat belt and shoulder harness installations must be mutually Jennifer Faye from SFI explains SFI Spec 16.1 Driver Restraint Assemblies Se hela listan på wescoperformance.com Tap to unmute. If playback doesn't begin shortly, try restarting your device. Up Next. Cancel. Autoplay is paused.

AS 2596. ECE R16. 3-Point Harness. C. Lap Sash Belt. AS 2596. ECE R16. AS E35. Seat belts as fitted to production cars as 19 Jun 2012 You can use expired belts for HPDE, just not racing. 60% of their strength over a 30 month time period thus the SFI two year rule. If you have a 3 inch belt that is folded over due to going around a seat edge or so All Belts (Shoulder, lap, Anti-Sub) must be installed to allow even tension across the entire width of the And here is SFI's Guide to Seat Belt Installation.